A home can be warm yet still feel stuffy, suffer condensation on cold mornings or bring in traffic noise whenever a window is opened. Mechanical ventilation with heat recovery (MVHR) addresses those everyday problems, but its performance is decided long before the unit is switched on. The work to prepare your home for MVHR installation needs to consider insulation, airtightness, duct routes and how your household actually uses each room.
MVHR continuously extracts warm, stale air from wet rooms such as kitchens, bathrooms and utility rooms. At the same time, it supplies filtered fresh air to bedrooms and living spaces, recovering much of the heat that would otherwise be lost. It can make a substantial difference to comfort and indoor air quality, particularly in a well-improved property. It is not, however, a replacement for dealing with draughts, damp or poor insulation first.
Start with the fabric of the building
MVHR works best in a home that retains heat well and has controlled air movement. If cold air is pouring through gaps around floors, loft hatches, pipe penetrations and old window frames, ventilation will be difficult to manage and the benefits of heat recovery will be reduced.
This does not mean making a home completely sealed. Every house needs fresh air, and older homes need particular care to manage moisture appropriately. The aim is to reduce unintended leakage, then provide the right amount of filtered ventilation where it is needed. A professional assessment can identify practical improvements, from loft insulation and cavity-wall work to draught-proofing around openings and service penetrations.
For a new build or deep retrofit, airtightness should be considered early, while junctions, membranes and services are still accessible. In an existing home, improvements can be phased around planned works such as a new kitchen, bathroom renovation, re-roofing or window replacement. The best approach depends on the construction of the property, its condition and the budget available.
Plan duct routes before finishes are fixed
Ductwork is the part of an MVHR system most likely to be overlooked. It needs a route from the central unit to every supply and extract valve, without excessive bends, crushed sections or awkward access points. Good duct design keeps airflow quiet, balanced and efficient.
In a self-build or major renovation, ducts can often run through ceiling voids, service zones, cupboards or a designed bulkhead. This is the simplest time to allow for the system. It may also be possible to position ducts within floor zones, depending on their depth and the structure of the building.
Retrofitting MVHR into a completed home requires more planning, but it is often achievable. A loft can provide useful space for upper-floor duct runs, while a utility room, airing cupboard, built-in wardrobe or under-stairs area may accommodate the unit. Some homeowners accept carefully designed ceiling bulkheads in hallways or bathrooms where alternatives are limited. The key is to agree these details before plastering, decorating or ordering bespoke joinery.
Give the unit a sensible home
The MVHR unit needs more than a spare corner. It should be installed where engineers can reach filters, condensate connections and controls for servicing. It also needs a suitable electrical supply and a route for the condensate drain.
Lofts are popular locations, but they must be properly insulated and accessible. A unit in an unheated, difficult-to-reach loft can be inconvenient to maintain and may need additional measures to protect ductwork and condensate pipework from cold conditions. A utility room or plant cupboard is often easier for regular filter changes, provided there is enough room and noise has been considered.
Ask early where outdoor intake and exhaust terminals will sit. They need adequate separation from one another and should avoid sources of pollution or odour, such as boiler flues, busy driveways, bins and kitchen extracts. Their external appearance should also be considered alongside brickwork, cladding and landscaping plans.
Prepare your home for MVHR room by room
MVHR is designed around the use of the home, not simply its floor area. Fresh air is normally supplied to living rooms, bedrooms, studies and other habitable spaces. Moist, stale air is extracted from kitchens, bathrooms, en-suites, cloakrooms and utility rooms. Air then travels through the property via gaps beneath internal doors or other planned transfer paths.
This is why floor plans, ceiling layouts and door specifications matter. If a new internal door fits tightly to the floor, air may not move between rooms as designed. If a planned extract valve clashes with a large pendant light, smoke alarm or ceiling beam, a late alteration can affect airflow or add cost.
Kitchen design deserves special attention. MVHR provides background extraction, but it does not usually replace a cooker hood that extracts directly outdoors. Steam, grease and strong cooking odours are better handled at source. Choose a cooker hood arrangement that works with the ventilation design, and discuss it before kitchen units are installed.
Bathrooms and utility rooms should be planned with moisture in mind. A well-designed MVHR system will continuously remove humid air, reducing the likelihood of condensation and mould. It is still sensible to address existing leaks, failed seals, penetrating damp or inadequate insulation. Ventilation cannot solve a building defect that is continually adding water to the fabric.
Avoid common installation compromises
The most expensive MVHR mistakes are often made when other trades are working quickly. Ducts may be squeezed into unsuitable voids, access panels omitted or insulation installed around components without considering future maintenance. A coordinated plan avoids these problems.
Where possible, keep duct runs short and straightforward. Use properly sized, rigid or semi-rigid ducting specified for the system, rather than treating ventilation ductwork as an afterthought. Insulate ducts running through cold spaces to limit heat loss and prevent condensation. Noise attenuation should also be included where required, especially near bedrooms and quiet living areas.
Do not assume that any available ceiling void will be large enough. Duct diameters, crossings, structural members, lighting positions and fire-stopping all need to be accounted for. Architects, electricians, kitchen designers, plumbers and builders should work from the agreed ventilation layout. This is particularly valuable when MVHR is being installed alongside an air source heat pump, underfloor heating or other low-carbon upgrades.
Commissioning is where performance is proven
A fitted system is not necessarily a finished system. Once the building works are complete, the installation must be commissioned. Each valve is adjusted so that supply and extract airflow rates match the design. The system controls should then be set up to suit the property and explained clearly to the homeowner.
This balancing process matters. Too little ventilation can leave humidity and pollutants lingering indoors. Too much can waste energy, create draughts or increase noise. A correctly commissioned system should provide steady background ventilation without making the home feel windy or intrusive.
You will also need to understand routine care. Filters normally need checking and replacing at intervals recommended for the system and local conditions. Homes near busy roads, agricultural activity or building works may require more frequent attention. External terminals should be kept clear, and any unusual noise, warning light or decline in airflow should be investigated rather than ignored.
Choose advice that looks at the whole house
MVHR is most effective when it forms part of a considered plan for the property. For some households, that plan may begin with insulation and airtightness improvements. For others, especially self-builders and major renovators, it can be designed alongside heat pumps, underfloor heating and hot-water provision from the outset.
At Baddow Eco Solutions, the starting point is the building and the people living or working in it. A proper assessment considers the age and layout of the property, existing services, planned refurbishment, comfort expectations and long-term running costs. That helps avoid specifying a ventilation system that looks good on paper but is difficult to install, maintain or live with.
A well-prepared MVHR project gives you more than a new ventilation unit. It gives your home a controlled supply of cleaner air, less dependence on opening windows in cold or noisy weather, and a better foundation for low-carbon heating. Speak with an experienced adviser before plans are finalised, and the decisions behind walls and ceilings can support comfort for many years.
